Having received the class certificate from Lloyd’s Register, the Q-Rohr® DFE has successfully passed its fourth class certificate. Special suitability of the explosion protection system for LNG and dual-fuel engines has also been confirmed by DNV-GL, Bureau Veritas and ABS (American Bureau of Shipping).

Gas-powered engines and the connected exhaust system for marine propulsion and power generation carry a major risk of explosion. This may be caused, among other things, by possible misfiring whereby a combustible gas-oxygen mix may reach the exhaust system. Sources of ignition mostly include hot surfaces in pipelines, turbochargers or glowing (soot) particles in the exhaust gas flow. When an explosive gas mixture meets with a source of ignition, there is the risk that pressure and flames will spread very quickly within the pipeline sections, thus usually causing damage or even uncontrolled destruction on components. This risk can lead to loss of manoeuvrability, devastating injuries and maritime distress.

The Q-Rohr® DFE is installed on the exhaust system of an engine. If an explosion occurs, it protects the engine through flameless venting technology. This reduces unacceptable overpressure, while the stainless steel mesh filter of the Q-Rohr® DFE absorbs the heat of the explosion. As a result, the explosion collapses, so that there is neither a strong shockwave nor flames. Pressure is safely relieved within the exhaust system, which remains intact. The engine room, too, receives maximum protection.

One benefit that is particularly important for ship operators is that, after an incident, the explosion vent in the Q-Rohr® DFE can simply be replaced and operation can be resumed.

Further product benefits

  • 100% seal tightness to eliminate danger of asphyxiation.
  • Compact, lightweight design and therefore suitable for installation within limited space
  • Connection flange in accordance DIN 86044
  • Corrosion-resistant: 100% stainless steel
  • Substantial noise reduction, even under normal operation

“Working together with the classification societies, we classified the Q-Rohr® DFE under major explosion volumes with stoichiometrically optimal gas concentrations and a variety of response pressures. This included simulating some worst-case scenarios, and the Q-Rohr® DFE passed all the tests with flying colours. The vessels equipped with the Q-Rohr® DFE include a purely LNG-based German ferry and several DFE-based container ships. Other projects are in progress,” says Roland Bunse, Q-Rohr® DFE developer and Senior Consultant in Explosion Safety

REMBE® is a global player in the areas of explosion safety, pressure relief, industrial measurement and sampling. Its strong growth over recent years has led to significant restructuring – and the founding of a new company. The way forward is clear: "Design a successful future – with Consulting. Engineering. Products. Service. And three strong companies.

In 2015, REMBE® GmbH Safety + Control underwent significant restructuring and a new company emerged: REMBE® Kersting GmbH.

Restructuring of REMBE® GmbH Safety + Control
REMBE® employees work in small, flexible and highly specialised teams in order to respond more rapidly and effectively to the demands of the market and the specific requirements of their customers. The company set up the following teams for every business unit: Global Sales, Technical Sales and Inside Sales.
The Global Sales team consists primarily of safety engineers with many years of experience in designing safety concepts in a wide range of industries. The Technical Sales team is composed of staff with special expertise in products and product development as well as technical documentation.

"We have made many changes over recent years. After founding eight world-wide subsidiaries, restructuring our sales department was the next logical step towards realising our unique selling proposition: Consulting. Engineering. Products. Service." says Stefan Penno, son of the company's founder Bernhard Penno and Managing Director of REMBE® GmbH Safety + Control since 2004.
The company believes that these four words sum up the difference between REMBE® and other companies operating in the same markets. REMBE® not only supplies products but also offers all the services, which plant operators require in the areas of explosion protection and pressure relief – from safety scans of existing plants and consulting services for planning new facilities to customised product development, start-up services and maintenance.

The birth of a new company – REMBE® Kersting GmbH
Over the decades, REMBE®'s Industrial Measurement division and Kersting GmbH Sampling + Grounding have independently established strong reputations as experts in the bulk materials industry. Their achievements were the inspiration behind the decision to merge the two entities into REMBE® Kersting GmbH. The new company combines all REMBE®’s specialist knowledge in bulk materials and supplies everything its global customers require for measurement, weighing, sampling and grounding. With a strong focus on productivity, it equips bulk material companies in a wide range of sectors with measurement technology, samplers and electrostatic grounding systems. At REMBE® Kersting, too, consulting, engineering and service complement the familiar product range of mass flow measurement, fill level control, sampler and ground monitoring technologies. "From measuring and weighing to sampling, our primary aim is always to make our customers' processes more efficient and productive. This requires more than high quality products. We also support our customers in planning, assembly, start-up and calibration," explains Jochen Eberheim, Managing Director of REMBE® Kersting GmbH. Dipl.-Ing. Jochen Eberheim is one of Germany's most experienced managers in the area of bulk materials and bulk material handling.



The 2nd Joint US and European DIERS Meeting was held in Dusseldorf from 10th to 12th June 2015 sponsored and organized by REMBE®. About 80 participants from 10 Countries listened to high quality presentations. Key topics were the modeling and experimental investigation of proper functioning of safety valves, experience and latest results of runaway reactions, lessons learned from incidents and the sizing of rupture disc vent line systems.

The participants got the opportunity to visit the production site of REMBE®, the german safety specialist for pressure relief and explosion safety. Its laser technology and the special type of disc opening are unique features for REMBE® rupture discs. They are among the most reliable safety devices for emergency vent lines worldwide. The participants were seriously impressed. In addition, open air explosion experiments showing the function of flameless venting and bursting plates completed the program to an outstanding event.

“The DIERS meeting in Dusseldorf was the best meeting within the last 20 years” mentioned Harold Fisher, the US chairman of the meeting. Prof. Jürgen Schmidt (European chairman) agreed and appreciated the support of the whole REMBE® team, ahead Sara Claramunt and the CEO Stefan Penno.

The 2nd Joint Meeting of the DIERS groups had motivated to repeat this kind of experience exchange.




The issue of the Safety Integration Level (SIL) is as complex as it is topical, as has been proved by the large number of committee activities of TRBS 2152-5, VDI 2180, NAMUR 138 and EN 15233. It is therefore high time to look at the issue in terms of explosion protection while at the same time considering the wider picture, looking beyond electric, electronic and programmable electronic systems (E/E/PE). REMBE® is the first company worldwide to offer SIL-equivalent parameters for mechanical (flameless) explosion venting products and the relevant signallers. For the first time manufacturers and operators are being enabled to meet existing as well as even tighter future requirements with regard to assessments of the safety of protection systems in explosion-prone environments.

So what does SIL involve?

When assessing the functional safety of a protection system it is above all important to ensure that its reliability matches the risks of a plant that is in danger. Such a SIL classification is based on a risk assessment that covers the probability of failure in a safety setup within a given scenario and the potential severity of any resulting damage. The defined tables and values, which can be found, for instance, in EN ISO 13849, lead to the required SIL level for the relevant (electronic) component. The higher the probability of occurrence and/or the potential severity of damage, the higher should be the requirements on the electronic componentry and also on the necessary SIL level. Any facilities with SIL level 4 certification thus offer the best risk minimisation and must be provided wherever probability and potential severity are especially high.


The risk assessment then forms the basis for an evaluation of measures designed to help reduce those two factors: probability of occurrence and potential severity of damage. The former is mitigated through preventive action, e.g. inertisation devices to prevent the occurrence of hazardous explosion-prone atmospheres). The severity of damage can be reduced through measures (e.g. explosion suppression systems).

SIL and “passive” explosion protection – REMBE® unites elements which belong together

SIL looks at the source which produces the functional safety of (E/E/PE) systems. The overall regulatory framework on which all certification is based is IEC 61508. Statements on the so-called “average probability of failure of the protective function at the point of requirement” have been available for quite a while as active protection systems, for instance, for REMBE®’s Q-Bic™ suppression systems.

Mechanical protection systems are not covered in this directive and cannot therefore be certified under it.

This has been the theory up to now. In practice, something else is required: Many plant manufacturers and operators in a variety of industries feel committed to SIL and demand that reliability parameters should also be available for mechanical protection systems, as they are often used in combination with (E/E/PE) systems and can only produce a consistent protection policy in its “overall effect”. Moreover a number of standards such as TRBS 2152-5 will expressly require certain SIL levels for protection systems in the future.

These practical requirements prompted REMBE® to take action: “Based on our close collaboration with customers and their planning and engineering offices, we are well aware that massive practical problems are likely to occur unless attention is paid to the safety gap of mechanical protection systems when reviewing the functional safety of explosion protection. With this in mind, we have set ourselves the task of finding a practical solution to the problem. After all, we are well aware of the vehement debates on the pros and cons of SIL outside electric, electronic and programmable electronic systems,” says Johannes Lottermann, PhD (Eng), Senior Consultant on Explosion Safety at REMBE®.

Based on these findings and its readiness for change, REMBE® has worked with IQZ, the German Institute of Quality and Reliability Management, in Wuppertal. Together, they have developed a transparent and legally sound methodology to assign SIL equivalents to REMBE® products despite their purely mechanical functions. The resulting PFD values (Probability of Failure on Demand) can thus be translated into “SIL language” under IEC 61508. It turned out that the company’s bursting disks had a SIL equivalent of 4, and the flameless venting devices a SIL equivalent of 2, due to the integrated electronic components of this SIL level.

“As we worked with renowned experts on the development of transparent methods in setting up PFDs, we are confident that the PFDs will be accepted in practice. REMBE® can be proud that, for the first time, this innovative approach is finally shedding some light into the darkness when it comes to assessing the functional safety of overall plant protection.
In a recent project, thanks to the SIL-equivalent parameters of our bursting disks, we helped a customer in New Zealand calculate the overall failure probability of their vented system which was protected by electronically controlled extinguishing barriers. This was a requirement specified by the relevant authority, and it was possible to complete the approval documents which, otherwise, would probably still be outstanding,” says Johannes Lottermann.

“The results of the relatively high SIL equivalents did not actually surprise us all that much,” says Stefan Penno, CEO of REMBE®. “It should be plausible to every engineer that a simple mechanical functional principle – like that of a bursting disk – is naturally more reliable than an electronic control circuit, despite all its sophistication and redundant backup systems.”

A dream has come true for two girls from the University of Namibia – a four-week internship in Germany

The company REMBE® has invited Ana and Kustaa from Windhoek to spend a month in Germany with an opportunity for some initial work experience. As both students have been studying German as a minor subject, the language barrier is only minimal. However, the cultural differences between Namibia and Germany are immense, and the two girls have therefore received a thorough induction in Windhoek. Also, REMBE® staff will be making a corporate effort to ensure that their Namibian guests have a good time in Brilon.

Their stay in Germany started, among other things, with a visit to the mayor of Brilon who gave them a very warm welcome to his town. Over the next few weeks, the two girls will be given an overall idea of each department at this medium-sized business, REMBE®. They can also look forward to a varied leisure programme during weekends.

REMBE®’s internship scheme with Namibia is a targeted social welfare programme, while at the same time encouraging opportunities for an international exchange. REMBE® wants to enable Namibian young professionals to gather some initial experience in a German company. “By creating this scheme,” says Annette Häger, member of the REMBE® Management Board, “we are showing how a company can be proactive in supporting young professionals internationally.”

The REMBE® initiative was welcomed by Onno Hückmann, the Ambassador of the Federal Republic of Germany in Namibia. When he spoke to Annette Häger, he emphasised the enormous importance of SMEs, in particular, to Germany’s economic success. He is especially pleased that REMBE® is acting as a pioneer in setting up the first programme of this kind in Namibia: “We need well-trained young people here in Namibia. Although there has been strong economic growth, the country still has a high level of unemployment.”

Achilles JQS (Joint Qualification System) is a supplier register and pre-qualification system used by the buyers in the Norwegian and Danish oil and gas sector...

... to manage supplier information and risk within the supply chain as well as to procure efficiently in accordance with EU regulations. Achilles JQS is a cost effective system where suppliers in an easy and standardised way can advice details on their company and products and services to potential customers in a fair, open and transparent way. This facilitates and simplifies the tender process, offering new business opportunities for both buyers and suppliers. - See more at:

Quality and quality management has always been at the heart of REMBE®’s business. In addition to the existing ISO 9001 certification and numerous other important quality accreditations, REMBE®’s Quality Management System has now been awarded ISO/TS 29001approval.

ISO/TS 29001 was developed specifically for the Oil & Gas industry and sets strict requirements on goods and services provided to ensure standardization and improvement within the sector. This latest certification constitutes an independent confirmation of REMBE®’s product and process quality as well as a demonstration of REMBE®’s commitment to the industry as a supplier.

The aim of ISO/TS 29001 was to provide a single QMS document to meet the needs of the oil and gas industries worldwide, specifically the major petroleum, petrochemical and natural gas organizations. Due to the inherent risks associated with the oil and gas industry, rigorous conformity to engineering, user and regulatory requirements are required. ISO/TS 29001 is available for use by manufacturers of oil and gas industry equipment and materials, service providers to the oil and gas industry, purchasers of equipment, materials, and services. The document can also be used for organizations to perform 2nd party auditing of their suppliers, as well as for the purpose of 3rd party certification.

With seven branch offices and over 150 staff members worldwide, REMBE® is the global market leader for flameless explosion venting and specialist for process safety and industrial measurement. Twice a year, all of REMBE®'s foreign staff members come together for the REX (REMBE® EXchange of Views and Ideas) event.

From February 13th to 14th, all employees learned about REMBE®’s latest technical innovations. “Our employees abroad in particular need to be trained about the latest technologies," says Stefan Penno, Managing Director of REMBE® GMBH SAFETY+CONTROL. Since the company values external expertise, Prof. Dr.-Ing. Juergen Schmidt from the Karlsruher Institut for Technology (KIT), an expert for safety in chemical plants, gave an intensive speech about the topic “risk management” and illustrated the need for intelligent protection concepts. His view is that “Protection is not something that is only paperwork it is the ethical attitude of all operators. Therefore, industrial plants need the best and most innovative protection of pressure and explosion”. Accidents in industrial plants happen on a daily basis and threaten human lives. The cooperation between KIT and REMBE® supports the active exchange with students and professors in order to develop new products for process safety.

As well as Professor. Schmidt, Dipl.-Ing. Richard Siwek, CEO of FireEx Consultant GmbH, presented potential hazard sources for dust explosions in plants and informed all participants about the possibilities of hazard analysis and the latest technical rules and standards. “The process of production has to be monitored permanently, in order to protect the plant against uncontrolled explosions” Mr. Siwek appealed to the audience.

REMBE® loves sweets!

In addition to the theoretical framework, Mr. Francesco Petruzzelli of REMBE®'s Italian branch, gave practical insight of how a manufacturer of sweets uses an integrated REMBE® protection concept. Here not only are production processes protected against dust explosions, but also their trucks during loading. Loading trucks can cause electro-static reactions, which can be avoided by using the grounding systems of REMBE®'s collaboration partner, KERSTING GMBH SAMPLING+GROUNDING. Thanks to REMBE® and KERSTING, the customer and especially his sweets are now safe.

REMBE® is now registered member of FPAL a supplier management community supporting the European Oil & Gas Industry.

FPAL supports the European Oil & Gas Industry with auditing for relevant suppliers. For more details please check



Intelligent explosion protection does not necessarily have to be expensive or complicated. New approaches and an innovative technology enable shock waves and flame jets to be diverted in a controlled manner from areas at risk of explosion. People and machines are thus protected in an effective way from devastating damage Dipl.-Ing. Roland Bunse, Till Möhle

First of all, an explosion is nothing but rapid burning up of a material within a few milliseconds. It is the reactive forces released by this, which spread into the surrounding area in the form of flame jets and shock waves that are especially dangerous.

The process occurs at a very high speed. Controlled action in the event of an explosion is therefore almost impossible, in contrast to a fire incident, which takes place relatively slowly. In this case, fast and correct intervention often prevents anything worse from happening.

If the bases for explosion protection are considered, only three preconditions have to be satisfied to cause a dust explosion:

On the one hand, a flammable medium in dust form, which is dispersed into a cloud, is necessary;


- On the other hand, oxygen must be present, in order that, with the dust, it can create an atmosphere that can cause an explosion;

-Finally, a small source of ignition is sufficient to ignite the mixture of air and dust. In this way, a fireball that is extremely dangerous for the area surrounding it can develop.

Preventing dust explosions

There are different approaches for preventing dust explosions. These are all aimed at reducing one of the three afore-mentioned factors, in order to minimise the probability of an atmosphere capable of holding dust in it, or of a dust explosion. Examples of these preventive measures are the inertisation of equipment and the avoidance of active sources of ignition. However, regular maintenance of equipment and machines and keeping surfaces clean also reduce the risk of a dust explosion.

In practice, however, there are numerous applications, in which one of the three factors cannot be reduced, or not to the necessary extent. The risk of an explosion cannot be absolutely excluded, even when all possible safety measures have been implemented. For this reason, it is important to make provisions for reducing the effects to a tolerable level in the event of an explosion. These provisions can be summarised under the general heading "constructive explosion protection".

Different Options

Protective measures against explosion can be implemented in different ways. The most current methods are listed below:

-; Explosion-resistant method of construction: when implementing this, a facility must be constructed in such a stable way that it can resist an excess pressure of at least 10 bars.

Explosion suppression: in the event of an explosion this will be detected in the shortest time possible. An extinguishing agent will then be blown towards the explosion, smothering the flames; in this way the dust explosion is suppressed.

- Explosion venting: bursting discs divert the shock waves and flame jets resulting from a dust explosion safely into the surrounding area. The bursting disc is designed and manufactured in accordance with the process conditions prevalent in the facility. At a specific pressure, as low as possible, the bursting disc opens and releases its cross section, the so-called venting area. In doing so, this venting area must be of an adequate size to safely allow an explosion to escape.

- Flameless pressure relief: If equipment or components are situated inside the buildings or in areas, in which a free pressure relief and the effects associated with it would cause damage, a flameless pressure relief is used. This way, the shock waves and flame jets are held back by a flame-trap affixed to the upper side of the bursting disc, so that there is no danger to the surrounding areas.

- Explosion decoupling: in the case of an explosion, the components of the equipment are decoupled from one another and from the remaining process; e.g. by non-return explosion valves. It is ensured that that the explosion does not propel the flame into equipment, which is upstream or downstream. The dust situated there would otherwise ignite and therefore trigger a secondary explosion.

It is essential to know the rim parameters and process conditions as precisely as possible for the construction of the explosion protection. It is necessary, therefore, for example, for the calculation of the required venting areas, to take account of the data regarding the equipment to be protected and of the exact key data about the existing material. 

Intelligent pressure relief  

A free pressure relief can only be guided into free, secured areas, due to the shock wave and the flame jet. In-facility traffic routes, close building developments or even public roads pose a problem time and again in the planning and implementation of such protection concepts. Operators often have no option but to determine very large areas at risk with safety distances around the installation for pressure relief. This additional expense means increased operating costs for the operator. The areas designated as safety areas may also no longer be used operationally, as entering them is extremely dangerous and is not permitted. It is precisely those traffic routes, which are used in-facility and also publicly, where a free pressure relief cannot therefore be implemented. Flameless pressure relief or explosion suppression is ideal protection concepts for keeping the effects of an explosion as low as possible. For many facility operators, however, a controlled pressure relief is a practicable alternative.

Problematic interpretation of standard specification

The diversion of the flames and shock waves into uncritical areas is addressed, amongst others, in Standard EN 14491. In Annex E of it, the use of so-called deflector plates is referred to. These are affixed in such a way that the effects of the explosion are diverted at an angle of 45° to approx. 60°.

The Standard does not mention, however, that the deflector plates must be constructed and fastened at great expense due to the tremendous repulsive forces. For a container of 20 m3, these forces amount to 50 kN (5 to), with an impetus of 25 kNs. In addition, these elements represent an enormous barrier during normal operation and take up valuable operational space.

New type of pressure relief

Against this background, the Brilon company, Rembe, has developed a new type of pressure relief. Targo-Vent is an opening angle delimiter, developed especially for bursting discs, which diverts the pressure relief into defined areas.

Targo-Vent cushions the bursting disc dynamically, progressively and can, therefore, elastically absorb large kinetic forces itself. The damper absorbs the enormous repulsive forces of the energy from the explosion and guides the explosion flames in the required direction. Depending on the conditions of application the flame is diverted upwards at a defined angle of approx. 30° to 45°. In this way, the shock wave and the flame jets are diverted into uncritical areas. This, in turn, allows the operator to minimise the safety areas around the vent openings and guarantees safe use of traffic routes. A further advantage in daily practice is that during normal operation Targo-Vent is assembled in a space-saving way on the bursting disc. No expensive baseplates or reinforcements are required. The system itself is made of maintenance-free stainless steel and does not cause any further current expenses.

Simple retrofitting

Targo-Vent is manufactured in all current bursting disc sizes, so that retrofitting in existing facilities can be implemented without any problems. The system, in combination with Rembe bursting discs and venting panels has been type-tested and authorised in accordance with the Atex Directive 94/9/EC (Atex 114) (FSA 13 Atex 1637). Targo-Vent is therefore suitable both as the initial equipment for new bursting discs and as retrofitting component for installations already existing. The user receives an intelligent explosion protection, which involves neither high costs nor complicated fitting. Shock waves and flame jets, which arise during a dust explosion, are guided into the right channels, so that people and machines are protected from devastating damages.

read more about TARGO-VENT

send enquiry